power_settings
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
power_settings [2021/01/17 03:15] admin created |
power_settings [2021/03/18 23:02] (current) admin |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| Below are power settings for common materials. | Below are power settings for common materials. | ||
| - | **1/8" | + | |
| + | * 1/4 in (6 mm) Cast Acrylic | ||
| + | * 1/8 in (3 mm) Plywood | ||
| + | * 1/4 in (6 mm) Plywood | ||
| + | * Glass | ||
| + | * Powder Coating | ||
| + | * Leather | ||
| + | * Granite | ||
| + | * Marble | ||
| + | * Melamine | ||
| + | * Rubber Stamps | ||
| + | | ||
| + | | ||
| + | ---- | ||
| + | |||
| + | **1/8 in (3 mm) Cast Acrylic** | ||
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/ | ||
| + | ^ Speed (Cut/ | ||
| + | |||
| + | |||
| + | **1/4 in (6 mm) Cast Acrylic** | ||
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/ | ||
| + | ^ Speed (Cut/ | ||
| + | |||
| + | **1/8 in (3 mm) Plywood** | ||
| | ^ 60 ^ 80 ^ 100 ^ 120 ^ | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| ^ Power (Cut/ | ^ Power (Cut/ | ||
| Line 8: | Line 34: | ||
| - | **1/4" | + | **1/4 in (6 mm) Plywood** |
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/ | ||
| + | ^ Speed (Cut/ | ||
| + | **Glass** | ||
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Engrave) | ||
| + | ^ Speed (Engrave) | ||
| + | |||
| + | **Powder Coating** | ||
| | ^ 60 ^ 80 ^ 100 ^ 120 ^ | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| ^ Power (Cut/ | ^ Power (Cut/ | ||
| ^ Speed (Cut/ | ^ Speed (Cut/ | ||
| - | **1/8" | + | **Leather** |
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/Engrave) | ||
| + | ^ Speed (Cut/Engrave) | | | | | | ||
| + | **Granite** | ||
| | ^ 60 ^ 80 ^ 100 ^ 120 ^ | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| ^ Power (Cut/ | ^ Power (Cut/ | ||
| ^ Speed (Cut/ | ^ Speed (Cut/ | ||
| + | **Marble** | ||
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/ | ||
| + | ^ Speed (Cut/ | ||
| - | **1/4" | + | **Melamine** |
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/Engrave) | ||
| + | ^ Speed (Cut/Engrave) | | | | | | ||
| + | **Rubber Stamps** | ||
| | ^ 60 ^ 80 ^ 100 ^ 120 ^ | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| ^ Power (Cut/ | ^ Power (Cut/ | ||
| ^ Speed (Cut/ | ^ Speed (Cut/ | ||
| + | **Cork** | ||
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/ | ||
| + | ^ Speed (Cut/ | ||
| + | |||
| + | **Corian** | ||
| + | | ^ 60 ^ 80 ^ 100 ^ 120 ^ | ||
| + | ^ Power (Cut/ | ||
| + | ^ Speed (Cut/ | ||
power_settings.1610874918.txt.gz · Last modified: 2021/01/17 03:15 by admin
Page Tools
