X700 Lasers

User Tools

Site Tools

Trace:
quick_start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
quick_start [2020/04/14 21:33]
127.0.0.1 external edit 		quick_start [2020/12/30 21:53] (current)
admin [Preparation]
Line 9: Line 9:
   * You should get about 5 gallons of distilled water.  Not purified water, not spring water, not mineral water, but distilled water.  This will be used for cooling your laser tube.   * You should get about 5 gallons of distilled water.  Not purified water, not spring water, not mineral water, but distilled water.  This will be used for cooling your laser tube.
   * If your laser didn't come with a chiller and you didn't purchase one separately, get two empty gallon jugs, fill them 3/4 full with water and freeze them.   * If your laser didn't come with a chiller and you didn't purchase one separately, get two empty gallon jugs, fill them 3/4 full with water and freeze them.
-  * Consider ordering eye protection of you don't have it.+  * Consider ordering eye protection if you don't have it.
   * Buy or acquire some material for your first projects.  Cardboard, paper, cast acrylic, and plywood are good options.   * Buy or acquire some material for your first projects.  Cardboard, paper, cast acrylic, and plywood are good options.
    
Line 16: Line 16:
 ====== Machine Setup ====== ====== Machine Setup ======
  
 +The laser is water cooled, so you need a chiller or at least a bucket with ice water.
 +
 +The pump that comes with it will probably be a submersible one that will sit in the water bucket.
 +
 +It connects to the water inlet on the machine and will have a return line that goes back into the bucket.
 +
 +You'll want to secure all the water connections with zip ties and be alert when you first turn on the pump for any leaks.
 +
 +There will also be an air pump that connects in the back near the water lines.  This provides air to the nozzle on the laser head and prevents soot from getting on the lens and also assists in cutting.
 +
 +There are power outlets on the back.  You should not use these unless you rewire the machine, but even then, you're better off using a separate wall outlet for the accessory components because they can introduce noise into your system otherwise.
 +
 +There is an exhaust fan that comes with the machine.  The machine should come with a hose but I don't think they include clamps, so you may need to buy some large hose clamps.
 +
 +The exhaust fan will suck the smoke and fumes from the cutting area and take it to the outside.
 +
 +You want the fan as close as possible to the outside so that the house is under negative pressure in your work area.  Otherwise, if there's a small leak, it will be pushing fumes out into your work area.
 +
 +You also need to have a way for fresh air to enter your workspace because the fan will not be able to just continually suck air out of the room without some new air replacing it.
 +
 + 
 ====== Software Setup ====== ====== Software Setup ======
  
 +The software that the machine uses is called [[http://www.rd-acs.com/|RD Works]].  You can install it off the cd or download it from rd-acs.com.
 +
 +[[http://lightburnsoftware.com|Lightburn]] is a better software for this machine but runs around $80 last I checked.  It has a free 30 day trial though.
 ====== First Project ====== ====== First Project ======
  
quick_start.1586918026.txt.gz ยท Last modified: 2020/04/14 21:33 by 127.0.0.1

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki